3035344 3054291 12V Stop Solenoid, Fuel Shut Off Solenoid for Cummins NTA855 N14 M11 K38 K50 Engine, Stop Fuel Shut Off Solenoid Replacement for AR5499 180208 134074

Product SpecificationsVoltage: 12V DC (nominal operating range: 10.5V - 14.5V)Plunger Type: Single-plunger, spring-extend to shut offCoil Type: G1380 with 180°C+ heat-resistant wrappingReplaces Part Numbers: 3035344, 3035345, 3035346, 3054291, 134074, 180208, 3018453, 3035362, 3054609, 3054610, 4024809, AR5499, AR5535, AR4361, AR1783Terminal Type: Two spade terminals (non-polarized, but ground is typically black)Coil Resistance: Approximately 10-18 ohms at 20°C (cold engine)Duty Cycle: Intermittent (energized only when engine runs)Compatible with Cummins Engine ModelsFor Cummins NTA855 (Natural, Turbocharged, Aftercooled)For Cummins N14 (all variants including Celect and Celect Plus)For Cummins M11 (all variants)For Cummins K38 (38-liter V12)For Cummins K50 (50-liter V16)For Cummins KT / KTA-19 (19-liter inline 6)Critical Usage NoteThis 12V fuel shut off solenoid is NOT compatible with 24V systems. Installing on a 24V for Cummins NTA855 (common in military and marine applications) will permanently damage the coil. Do not manually override the plunger while the engine is running. If the engine fails to stop after installing this 3035344 stop solenoid, check for binding in the fuel rack linkage.

• 🔌 Voltage Verification Required - This fuel shut off solenoid operates on 12V DC only. Before ordering the 3035344 stop solenoid for Cummins NTA855, verify your engine uses a 12V electrical system. Installing this 12V stop solenoid on a 24V engine will burn the coil instantly. Check your old solenoid voltage stamp or measure across the wires with key ON.
• 📋 Multiple Part Number Cross-Reference - This 3054291 stop solenoid replaces these part numbers: 3035344, 3035345, 3035346, 3054291, 134074, 180208, 3018453, 3035362, 3054609, 3054610, 4024809, AR5499, AR5535, AR4361, AR1783. Match any of these numbers to your old unit before installing this 12V fuel solenoid for Cummins engine.
• 🛑 Engine Shutdown Function - This 3035344 fuel shut off solenoid cuts fuel supply when de-energized. When you turn off the ignition for Cummins N14 or M11, power is removed from the 12V stop solenoid. The spring-loaded plunger extends to block the fuel rack, stopping the engine within 3 seconds. This safety feature prevents engine runaway on K38 and K50 diesel engines.
• 🔥 High Temperature Coil Protection - This 3054291 stop solenoid features a G1380 coil wrapped with heat-resistant material rated above 180°C (356°F). The 12V solenoid withstands under-hood temperatures for Cummins NTA855 and KTA-19 engines where cheaper solenoids fail. The coil insulation prevents short circuits that cause intermittent shutdown or complete failure.
• 🔧 Installation with O-Ring Seal - This single-plunger 12V fuel solenoid includes a new O-ring seal. Remove the old 3035344 solenoid from the injection pump housing. Clean the mounting bore before inserting the new 3054291 stop solenoid. Tighten to 15-20 Nm (133-177 in-lbs). Do not overtighten, which cracks the housing for Cummins N14 or M11 engine.